12/28/2023 0 Comments Linksys wrt54g wired client listFinding this great thread, I thought I'd try playing with turning the WRT54G into a wireless bridge and it seems to work great! Here's what I did.Ĭable Modem->DIR-655-> Vonage PAP2, TiVo, Slingbox I just replaced my trusty WRT54G v2 with a DIR-655 to serve as my main router in the house. SPI Firewall has also been disabled on the security page. "Assign WAN Port to switch" has been checked on setup page. STP (spanning tree protocol) has been disabled on the setup page. Update: I installed wireshark on the computer behind client router and according to the logs, 150 (computer behind client) sees 121's (computer behind main router) ping requests. I think if I can get the computer behind the client router to respond, I can ping it. But when I disconnected the cable, that disconnected it from the network. It looks like that the icmp_seq 1 through 143 were sent and recieved. I don't know if this fact is relevant or not. PING 192.168.1.150 (192.168.1.150) 56(84) bytes of data.īut if i disconnect the ethernet cable between the client router and the computer, I get messages:įrom 192.168.1.121 icmp_ seq=144 Destination Host Unreachableįrom 192.168.1.121 icmp_ seq=145 Destination Host Unreachable It is like the packets are lost or something. When I ping a computer behind client router with a computer behind main router. If I put it in "Client" mode, I can't ping the client router from a computer behind my main router any more.Īlso, a note of interest. Otherwise, I followed the instructions per the first post. I had to use "Client Bridge" mode in order to ping my client router from a computer behind my main router. I copied and pasted the command into the terminal onto the client router via the terminal, but it did not work. I followed the instructions on step 10 of the first post. What do I do?Ĭlick to expand.I have several days but I still can NOT ping computer behind my client router from computers behind my main router. However, after getting home today, I discovered that Azureus was giving me a "Firewalled NAT" error, and I can't ping my desktop anymore. I also forwarded my Azureus port to 192.168.1.129 and 192.168.1.130, and turned UPnP on on both routers, allowing me to us Azureus with no problem. I entered that Telnet command, and I could ping my desktop with my laptop (192.168.1.105, static) that was connected to my first router's wireless network just fine. I entered a static IP of 192.168.1.130 on my desktop that is wired to the Alchemy WRT54G, used OpenDNS, and my internet connection is currently working just fine. I wanted to turn DHCP off, but I didn't know how else to send my internet connection to the Alchemy WRT54G. It's getting a connection via cable and is sending the connection via DHCP to my other WRT54G (Alchemy, 192.168.1.129). My main router is a WRT54G running default firmware (192.168.1.1). I followed all the instructions and everything seemed to be working fine yesterday. How many WDS units are needed? It depends on your specific environment (that is a good the reason to buying WDS units one at the time, try it, and decide on the Next step).Īlright, I have a slight problem. ) has to be placed in spots were the signal is good about Half way to the dead spots. and spot with weak, or No signal.Įvaluate how you can cover the space and start placing WDS units.Īdditional Wireless Routers in WDS Mode (Wireless Network - Configuration Modes. Using a Laptop loaded with ith Netstumbler, do a Wireless survey in the house, Īccording to the Netstumbler's signal strength reading, identify spots that have strong signal.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |